VACS:Projects:Hardware:LPS:Connectors
From VACS
(Difference between revisions)
| Line 61: | Line 61: | ||
<td></td> | <td></td> | ||
<td>MOSFET driver current selector 0.22 ohm (active low)</td> | <td>MOSFET driver current selector 0.22 ohm (active low)</td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | |||
| + | == LCD Panel == | ||
| + | <table cellpadding="0" cellspacing="0" border="1"> | ||
| + | <tr> | ||
| + | <td>1</td> | ||
| + | <td>GND</td> | ||
| + | <td width="20px"></td> | ||
| + | <td></td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>2</td> | ||
| + | <td>VROT</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>Rotative wheels output voltage</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>3</td> | ||
| + | <td>VBUTTON</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>Buttons output voltage</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>4</td> | ||
| + | <td>LCD_BACKLIGHT</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LCD backlight driver (active high)</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>5</td> | ||
| + | <td>LED_1</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LED supply 1 (active high)</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>6</td> | ||
| + | <td>LED_2</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LED supply 2 (active high)</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>7</td> | ||
| + | <td>LED_3</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LED supply 3 (active high)</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>8</td> | ||
| + | <td>LED_4</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LED supply 4 (active high)</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>9</td> | ||
| + | <td>LCD_CLK</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LCD serial clock</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>10</td> | ||
| + | <td>LCD_D</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LCD serial data</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>11</td> | ||
| + | <td>LCD_CS</td> | ||
| + | <td width="20px"></td> | ||
| + | <td>LCD chip select (active low)</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>12</td> | ||
| + | <td>+5V</td> | ||
| + | <td width="20px"></td> | ||
| + | <td></td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
Revision as of 13:59, 18 November 2006
This page describes the connectors of the hardware boards.
Rectifier Board
| 1 | IS11 | MOSFET driver current selector 0.22 ohm (active low) | Power supply 1 | |
| 2 | IS12 | MOSFET driver current selector 0.66 ohm (active low) | ||
| 3 | RE1 | Power supply relay selector (active high) | ||
| 4 | Io1 | Output current measure | ||
| 5 | -5V | |||
| 6 | +24V | |||
| 7 | Io2 | Output current measure | Power supply 2 | |
| 8 | RE2 | Power supply relay selector (active high) | ||
| 9 | IS22 | MOSFET driver current selector 0.66 ohm (active low) | ||
| 10 | IS21 | MOSFET driver current selector 0.22 ohm (active low) |
LCD Panel
| 1 | GND | ||
| 2 | VROT | Rotative wheels output voltage | |
| 3 | VBUTTON | Buttons output voltage | |
| 4 | LCD_BACKLIGHT | LCD backlight driver (active high) | |
| 5 | LED_1 | LED supply 1 (active high) | |
| 6 | LED_2 | LED supply 2 (active high) | |
| 7 | LED_3 | LED supply 3 (active high) | |
| 8 | LED_4 | LED supply 4 (active high) | |
| 9 | LCD_CLK | LCD serial clock | |
| 10 | LCD_D | LCD serial data | |
| 11 | LCD_CS | LCD chip select (active low) | |
| 12 | +5V |
