VACS:Projects:Hardware:LPS:Connectors
From VACS
(Difference between revisions)
(→Rectifier Board) |
|||
| Line 2: | Line 2: | ||
==Rectifier Board== | ==Rectifier Board== | ||
| + | The rectifier board is connected to the power supply microcontroller board for the control and measurement of the output current. For the power distribution it has several one wire high power | ||
| + | connectors (not described here). | ||
<table cellpadding="0" cellspacing="0" border="1"> | <table cellpadding="0" cellspacing="0" border="1"> | ||
| Line 35: | Line 37: | ||
<tr> | <tr> | ||
<td>6</td> | <td>6</td> | ||
| − | <td> | + | <td>gndref</td> |
| + | <td></td> | ||
| + | <td>Ground reference for current measurement</td> | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
<td>7</td> | <td>7</td> | ||
| + | <td>gndref</td> | ||
| + | <td></td> | ||
| + | <td>Ground reference for current measurement</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>8</td> | ||
| + | <td>+24V</td> | ||
| + | </tr> | ||
| + | <tr> | ||
| + | <td>9</td> | ||
<td>Io2</td> | <td>Io2</td> | ||
<td></td> | <td></td> | ||
| Line 45: | Line 59: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| − | <td> | + | <td>10</td> |
<td>RE2</td> | <td>RE2</td> | ||
<td></td> | <td></td> | ||
| Line 51: | Line 65: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| − | <td> | + | <td>11</td> |
<td>IS22</td> | <td>IS22</td> | ||
<td></td> | <td></td> | ||
| Line 57: | Line 71: | ||
</tr> | </tr> | ||
<tr> | <tr> | ||
| − | <td> | + | <td>12</td> |
<td>IS21</td> | <td>IS21</td> | ||
<td></td> | <td></td> | ||
| Line 63: | Line 77: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
== LCD Panel == | == LCD Panel == | ||
Revision as of 15:30, 26 November 2006
This page describes the connectors of the hardware boards.
Rectifier Board
The rectifier board is connected to the power supply microcontroller board for the control and measurement of the output current. For the power distribution it has several one wire high power connectors (not described here).
| 1 | IS11 | MOSFET driver current selector 0.22 ohm (active low) | Power supply 1 | |
| 2 | IS12 | MOSFET driver current selector 0.66 ohm (active low) | ||
| 3 | RE1 | Power supply relay selector (active high) | ||
| 4 | Io1 | Output current measure | ||
| 5 | -5V | |||
| 6 | gndref | Ground reference for current measurement | ||
| 7 | gndref | Ground reference for current measurement | ||
| 8 | +24V | |||
| 9 | Io2 | Output current measure | Power supply 2 | |
| 10 | RE2 | Power supply relay selector (active high) | ||
| 11 | IS22 | MOSFET driver current selector 0.66 ohm (active low) | ||
| 12 | IS21 | MOSFET driver current selector 0.22 ohm (active low) |
LCD Panel
| 1 | GND | ||
| 2 | VROT | Rotative wheels output voltage | |
| 3 | VBUTTON | Buttons output voltage | |
| 4 | LCD_BACKLIGHT | LCD backlight driver (active high) | |
| 5 | LED_1 | LED supply 1 (active high) | |
| 6 | LED_2 | LED supply 2 (active high) | |
| 7 | LED_3 | LED supply 3 (active high) | |
| 8 | LED_4 | LED supply 4 (active high) | |
| 9 | LCD_CLK | LCD serial clock | |
| 10 | LCD_D | LCD serial data | |
| 11 | LCD_CS | LCD chip select (active low) | |
| 12 | +5V |
